Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Furi Gustogrip FUR812 paring 4" 0.075 CrMoV 56 23 diamonds to 1000/strop to .05 top B Kitchen
 
Authors Comments:This finish leaves a refined but toothy edge that seems to work better.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Furi Lil Edgy Santoku 5" .105 CrMoV 56 23 diamonds to 1000/strop to .05 top B Kitchen
 
Authors Comments:This finish leaves a refined but toothy edge that seems to work well for kitchen duty..
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JamesBell
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT Onion-Shenanigan #K470KKP 3.25 inch 0.119 inch / 3.0mm Acuto 59-60 HRC 20* 0.6 ceramic Upper holes B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Seal Pup Elite 4.9 0.19 AUS 8 57-58 20 Leather Stops 0.5 Bottom B Bushcraft, camping, field work
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
20 deg
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Alpha Hunter 3.5" ? 420HC ? 17 1000# diamond, a few light cleanup passes with 5um leather Bottom B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Precision Hunter (1446) 3.3125" ? 440A ? 17 1000# diamond, a few light cleanup passes with 5um leather Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 915 Triage 3.5" 0.13" N680 57-59HRC 20 1um Strops Bottom B
 
Authors Comments:I rested the spine on the closest pin of the depth key and then rotated the blade until most of it was parallel to the base of the sharpener.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Zero Tolerance zt0350 3 1/4 .121 S30V Unk 20 deg. MicroFine-Fine Bottom B EDC
 
Authors Comments:MicroFine finish after 600g diamond stone
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 10 of 20