Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Buck Zipper. 191 4 1/8 inch 0.14 inch 420HC ? 18/side. Leather strop 1mic Upper B.5 Skinning fixed blade
 
Authors Comments:Buck states factory angles are 13-16/side. This was closer to 18/side. Diamond 400 - 1000. Ceramic 1.4 then leather strops as noted in finish.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Wicked Edge Hunting Knife 4 in. .125 in. AUS-8 Unk. 18 deg. 14m Leather Bottom B.5 Hunting / Camping
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kai Shun DM-0716 4 inch / 100 mm 1.5 mm VG-MAX 61 16 0.5 um leather strop T B.0 Kitchen paring knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fallkniven TK-1 4 inches .18 inches 3G laminated powder 62 21 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.4 bushcraft
 
Authors Comments: LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Heckles Professional S paring 4 inches ? "High carb stainless ? 17.8 ? Above upper holes B Kitchen
 
Authors Comments:Diamond: 600 to 1000. Ceramic:1200 to 0.6 mic. Final: naniwa 8k
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Military CF 4" .156" S90V unknown 15 3.5um Bottom. B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
SOG Field Pup 4" .125" AUS-8 57-58HRC 20 1600# Top A.5 Field Dressing, Skinning
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 15 of 20