Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Mora Frost Exclusive 345 125 mm 3 mm ? ? 22 1000# Diamond Top C Outdoor / fishing
 
Authors Comments:This is a knife I have been using since the late '70.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
IKEA Utility knife 120 mm 1.35 mm Cheap stainless 54 22 0.6 um micro fine T B.0 Onion and larger veggies in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Strider GW/AR152 8" .250 S30V unknown 25 3.5 micron Bottom C OCONUS deployment
 
Authors Comments:I'll check the hardness when I see the knife again
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Boker Plus Toucan multi tool neck knife 1.02 inches / 2.6cm 0.2 inches / 5mm 440c 58 HRC 22* factory angle 0.6 mic ceramic Level @ grind line 0.8 A Neck knife multi tool
 
Authors Comments:Depth level with grind line
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Leatherman PST-original Leatherman multi-tool 2.9 inches ? 420 HC STAINLESS ? 20 1200 ceramic Above upper holes A.5 Multi tool/ anything goes
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kai Shun DM-0706 200mm 1mm VG-10 61 ± 1 HRC 16 0.5 um leather strop Bottom D.0 Misc kitchen use
 
Authors Comments:Refined the factory (16 degrees) edge, got scary sharp and passed HHT.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Dragonfly 58 mm 2.5 mm VG-10 HRC 59-61 15 Micro fine ceramic stones (0.6 um) Top 1 or 2 matches A.0 Light EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cutco 2 3/4" paring Item # 1720 2.75 - 440A - 17 1000# then 5-3.5 leather strops spine only in vice A.5 kitchen, general use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
A.5, 17 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 3 of 20