Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Kai Shun DM-0716 4 inch / 100 mm 1.5 mm VG-MAX 61 16 0.5 um leather strop T B.0 Kitchen paring knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kai Shun DM-0710 Filleting knife 150 mm 1.7 mm VG-10 HRC 61 16 0.5 um leather strop T C.0 Handling fish in the kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar/Becker BK16 4.375 ? 1095 56-58 20 1600 ceramic Bottom B 0.75 ?
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
?
Setting 2:
?
Setting 3:
?
Setting 4:
?
Setting 5:
?

 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Becker bk2 (new model) 5-1/4" 0.250 1095 Cro-Van 56-58 HRC 20 degrees 3.5um Bottom. B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kabar K2 Chinchete 3.25" 0.15" 3CR13 50-52 18 3.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar 1100 stockman pocket knife 2.5 inch ? ? ? 21.75 Ceramic 0.6 micron Above upper holes A.5 Toolbox
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Precision Hunter (1446) 3.3125" ? 440A ? 17 1000# diamond, a few light cleanup passes with 5um leather Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
J. A. Henckels Professional "S" 31021-160 Chef 6" 3mm X50CrMoV15 ? 20 2k Chosera Bottom C Chopping and Slicing
 
Authors Comments:Not the greatest steel, doesn't hold its edge well, especially below 20 degrees. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 9 of 20