Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Spyderco Endura 4 FFG 3.75" 0.125" ZDP-189 HRC 64 18 0.5um Top B.0 EDC
 
Authors Comments:Holds an edge really well.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
ESEE ESEE-4 4.5 inches 3/16th inch 1095 carbon 57 22 degrees ceramics and strops with 5 and 3.5 micron pastes, I do a lot of stropping with green paste day to day and so I get a convexing to this edge over time top B.75 bushcraft and survival
 
Authors Comments:a stout and very sharp edge, takes abuse well- LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
ESEE ESEE-5 5.45 inches .25 inches 1095 cabon steel 57 17-19-21 convexed ceramics then strops 5 and 3.5 pastes to integrate the shoulders top B-5 bushcraft and survival
 
Authors Comments:This knife is essentially a pry bar with a sharp edge. It is a beast developed to help downed helicopter pilots to escape from their wreckage. A great knife to carry around in your car for emergencies. LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
ESEE ESEE-6 6.5 inches 3/16th inch 1095 cabon steel 57 20 degrees- frighteningly sharp ceramics and strops with 5 and 3.5 micron pastes, I do a lot of stropping with green paste day to day and so I get a convexing to this edge over time Top C survival/bushcraft, a good slicer in the kitchen
 
Authors Comments: all the ESEE knives are full flat-ground and the blades vary in thickness from the spine to the edge, so they are good slicers but hard to mount in the vise.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kershaw ET 3.25" 0.120" Sandvik 14C28N Not listed 20 1000 grit diamond, 5um paste on leather optional Top A.5 General light utility
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Hogue EX01 - 4" 4 . 154cm 57-59 20 Ceramic 1600 Bottom B 0.25 .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Hogue EX01 Tanto 4" 0.15" 154CM 57-59 22 1k diamond, any diamond paste strop for personal taste. Handles micro-bevels very well! Top B.5 Heavy duty utility/carry
 
Authors Comments:The cosmetic jimping on the spine makes a great reference point on the depth key pins
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber EZ Out 3 .1 high carbon stainles n/a 17.5 1000# then 5-3.5 leather strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
1000# 17.5 deg., stop @ 16.5
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Field Pup 4" .125" AUS-8 57-58HRC 20 1600# Top A.5 Field Dressing, Skinning
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Anders Petter Fillet knife 150 mm 1.6 mm Molybdenum stainless 57 21 0.6 um micro fine T C.0 Filleting of fish in kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 8 of 20