Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 551 Griptilian 3.45" .115" 154CM 58-60HRC 18 deg. w/ 20 deg. microbevel 3.5m on Balsa Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Tanto 3.5 .115 154CM 59 18 .05 strop with a 1600 microbevel @22 top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
18 degrees to .05 strop
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
8		 Rating:
 Rating:
 Rating:
 Rating:
Hogue EX01 - 4" 4 . 154cm 57-59 20 Ceramic 1600 Bottom B 0.25 .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Emerson CQC-8 100 mm 3 mm 154CM? 57-59 23 1000# Diamond Bottom B Hard use survival / bushcraft
 
Authors Comments:This folder is from 2004 without wave. I have a V-grind on this one.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fallkniven PXL Folder 3.4 inches .138 3 G Powder steel lam 62 16 ceramics and strops Top B EDC
 
Authors Comments:This is my favourite EDC knife. It is pretty and it is sharp in the extreme. I give this knife a five out of five for looks, usefullness and strength.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kabar K2 Chinchete 3.25" 0.15" 3CR13 50-52 18 3.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fallkniven TK-1 4 inches .18 inches 3G laminated powder 62 21 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.4 bushcraft
 
Authors Comments: LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 3 of 20