Thank you, please put me on the waiting list!

Simply WOW!

Clay,

So the big question, any ideas on approximately when this accessory will be available? Put me down on the waiting list NOW!

Thanks,

Mark

Clay,

Thank you for the response, I was about there but your post provided full clarification. Thanks for taking the time to provide more insight to the potential accessory. Since many of us us the diamonds, ceramics and choseras, I believe you will have great interest in this accessory. I can tell you that I would for sure be interested especially if the concept proves out to be as accurate as using the angle cube.

Phil - thanks for the link!

Thanks again,

Mark

Clay,

I will bite. For those of us not familiar with the concept of the design enhancement, how about a little more information on what the purpose of the design change is and how it works?

Thanks,

Mark

Thanks for all of the input folks, it seems I just need more time and experience with using the Chosera stones.

Thanks,

Mark

Thanks Ken! Yes, I do have all of the diamonds and both sets of ceramics. Since this was my first attempt with the Choseras, I thought I would just see for myself how things turned out after the 600 diamonds. Just can't figure out why the left side turned out great and the right side is not.

Thanks again,

Mark

Hello Everyone,

All, I am looking for some some suggestions/advice on using my new Chosera stones. I have 800/3000 and 5000/10000 Chosera stones. I profiled a knife using the 600 diamonds to a very nice even and smooth bevel (very flat and perfect not considering the scratches) and then proceeded through the Choseras. On the left side, the bevel is great and I am extremely pleased with the results, but the right side has bright and cloudy spots all over the bevel. I went back and flattened the edge with the diamond stones and started over ensuring I was using very light pressure with the 800 Chosera stone and the same thing is happening. I have ensured that the 13 degree edge has been maintained using the angle guage with each stone. Is it possible that the stones already need to be lapped during their first use? Anyone have any suggestions on why this is happening? I realize not seeing the bevel makes things very difficult to diagnose, but I would appreciate any advise you all may be willing to offer based on your experience. I have watched Tom's videos on using the Chosera stones on the WEPS as well as his video on lapping and they are very helpful.

I realize I may just need more experience with using the stones to obtain the appearance I am seeking, but any tips on how to deeply shorten the learning curve on the Chosera stone use would be most appreciated.

Thank you in advance for your time!

Mark

Tom and Philip thanks for your input and recommendations. Also, thanks again to everywone for your time and recommendations. I ordered an 800/3000 and 5000/10000. I am sure I will like the results and if so, over time I can add additional combination of grits in the stones to fill the gaps.

Thanks you!

Mark

Thank you all for your time and responses!

Mark

Earnon,

Thank you very much for your reply and information. Sounds like you are getting plenty of experience with your new stones!

All,

I have read through many posts on the forum concerning Chosera Stones and have found some pertinent information as to what I am looking for but if one had a goal of producing a mirror edge while balancing cost of stones with a limitation of purchasing only two sets of Chosera Stones (to reduce costs), what grit stones would you recommend considering I have the PPII and both sets of ceramic stones. Any and all feedback welcome, but would love to hear from Clay, Ken, Philp and Tom and anyone else with experience with the Chosera stones.

Thanks,

Mark

Awesome idea!

Hello,

I have not experienced this, but there some very small hex keys, down to .5mm or so. If the hex key will not work, then my only suggestion is to simply raise the knife up in the vice clamp.

Mark

Hello,

I have been using a set of hex keys to adjust the blade height - just put a hex key on top of the height adjustment prongs. Can easily change the height by using different size hex keys. For ease in producing the result in the future, just jot down the size hex key used.

Mark

Thank you sir. Your insight and willingness to share is much appreciated!

Tom,

Thank you for the clarfication. Care to comment on your experience or pros and cons of each method?

Some folks have stated that they helped this situation by grinding off the plastic edges of the stones to be even with the diamond plates. For me, it was not worth the effort for such a small area.

Would someone be so kind and define "Edge Leading" and "Edge Trailing"?

Thanks,

Mark

Here are the pictures - I hope.

Thanks,

Mark